root@data20:/home/tpm# smartctl --all /dev/sda
smartctl 5.40 2010-07-12 r3124 [i686-pc-linux-gnu] (local build)
Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net

=== START OF INFORMATION SECTION ===
Device Model: ST31000524AS
Serial Number: 9VPBWD5S
Firmware Version: JC45
User Capacity: 1.000.204.886.016 bytes
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 8
ATA Standard is: ATA-8-ACS revision 4
Local Time is: Sat Jul 9 15:03:52 2011 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 600) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 171) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x103f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 117 100 006 Pre-fail Always - 150169914
3 Spin_Up_Time 0x0003 100 100 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 29
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 062 060 030 Pre-fail Always - 1761313
9 Power_On_Hours 0x0032 099 099 000 Old_age Always - 1716
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 29
183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
188 Command_Timeout 0x0032 100 099 000 Old_age Always - 1
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 061 047 045 Old_age Always - 39 (Lifetime Min/Max 38/40)
194 Temperature_Celsius 0x0022 039 053 000 Old_age Always - 39 (0 24 0 0)
195 Hardware_ECC_Recovered 0x001a 024 022 000 Old_age Always - 150169914
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 141858474821360
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 690836248
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 1750992578

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 1716 -

SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

root@data20:/home/tpm#










root@data20:/home/tpm# smartctl --all /dev/sdb
smartctl 5.40 2010-07-12 r3124 [i686-pc-linux-gnu] (local build)
Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net

=== START OF INFORMATION SECTION ===
Device Model: ST31000524AS
Serial Number: 9VPBYER8
Firmware Version: JC45
User Capacity: 1.000.204.886.016 bytes
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 8
ATA Standard is: ATA-8-ACS revision 4
Local Time is: Sat Jul 9 15:04:45 2011 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 600) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 170) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x103f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 117 099 006 Pre-fail Always - 133513359
3 Spin_Up_Time 0x0003 100 100 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 22
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 064 060 030 Pre-fail Always - 2829097
9 Power_On_Hours 0x0032 099 099 000 Old_age Always - 1703
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 22
183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 061 046 045 Old_age Always - 39 (Lifetime Min/Max 38/40)
194 Temperature_Celsius 0x0022 039 054 000 Old_age Always - 39 (0 26 0 0)
195 Hardware_ECC_Recovered 0x001a 025 023 000 Old_age Always - 133513359
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 89863600735947
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 3589224590
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 2844563909

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 1703 -

SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

root@data20:/home/tpm#









root@data20:/home/tpm# smartctl --all /dev/sdc
smartctl 5.40 2010-07-12 r3124 [i686-pc-linux-gnu] (local build)
Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net

=== START OF INFORMATION SECTION ===
Model Family: Hitachi Deskstar 7K1000.C
Device Model: Hitachi HDS721010CLA332
Serial Number: JP2940HD087WVC
Firmware Version: JP4OA3EA
User Capacity: 1.000.204.886.016 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 8
ATA Standard is: ATA-8-ACS revision 4
Local Time is: Sat Jul 9 15:16:37 2011 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status: (0x85) Offline data collection activity
was aborted by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (9812) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 164) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail Always - 0
2 Throughput_Performance 0x0005 134 134 054 Pre-fail Offline - 100
3 Spin_Up_Time 0x0007 163 163 024 Pre-fail Always - 194 (Average 271)
4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 73
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 136 136 020 Pre-fail Offline - 32
9 Power_On_Hours 0x0012 100 100 000 Old_age Always - 5569
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 73
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 259
193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always - 259
194 Temperature_Celsius 0x0002 130 130 000 Old_age Always - 46 (Lifetime Min/Max 25/66)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 4423

SMART Error Log Version: 1
ATA Error Count: 278 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 278 occurred at disk power-on lifetime: 5532 hours (230 days + 12 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 01 16 ff 67 0d Error: ICRC, ABRT 1 sectors at LBA = 0x0d67ff16 = 224919318

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 0f ff 67 e0 00 15d+00:54:35.181 READ DMA EXT
b0 d0 01 00 4f c2 00 00 15d+00:54:33.915 SMART READ DATA
25 00 08 07 ff 67 e0 00 15d+00:54:33.903 READ DMA EXT
27 00 00 00 00 00 e0 00 15d+00:54:33.901 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 02 15d+00:54:33.852 IDENTIFY DEVICE

Error 277 occurred at disk power-on lifetime: 5532 hours (230 days + 12 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 01 0e ff 67 0d Error: ICRC, ABRT 1 sectors at LBA = 0x0d67ff0e = 224919310

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 07 ff 67 ed 00 15d+00:54:31.477 READ DMA EXT
25 00 08 ff fe 67 ed 00 15d+00:54:31.475 READ DMA EXT
25 00 08 f7 fe 67 ed 00 15d+00:54:31.474 READ DMA EXT
25 00 08 ef fe 67 e0 00 15d+00:54:31.457 READ DMA EXT
ec 00 01 00 00 00 00 00 15d+00:54:31.422 IDENTIFY DEVICE

Error 276 occurred at disk power-on lifetime: 5532 hours (230 days + 12 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 01 d6 fe 67 0d Error: ICRC, ABRT 1 sectors at LBA = 0x0d67fed6 = 224919254

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 cf fe 67 ed 00 15d+00:51:22.170 READ DMA EXT
25 00 08 c7 fe 67 ed 00 15d+00:51:22.167 READ DMA EXT
25 00 08 bf fe 67 e0 00 15d+00:51:22.105 READ DMA EXT
27 00 00 00 00 00 e0 00 15d+00:51:22.103 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 02 15d+00:51:22.053 IDENTIFY DEVICE

Error 275 occurred at disk power-on lifetime: 5532 hours (230 days + 12 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 01 c6 fe 67 0d Error: ICRC, ABRT 1 sectors at LBA = 0x0d67fec6 = 224919238

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 bf fe 67 e0 00 15d+00:48:13.041 READ DMA EXT
27 00 00 00 00 00 e0 00 15d+00:48:13.039 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 02 15d+00:48:12.989 IDENTIFY DEVICE
ef 03 42 00 00 00 a0 02 15d+00:48:12.942 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 15d+00:48:12.941 READ NATIVE MAX ADDRESS EXT

Error 274 occurred at disk power-on lifetime: 5532 hours (230 days + 12 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 01 c6 fe 67 0d Error: ICRC, ABRT 1 sectors at LBA = 0x0d67fec6 = 224919238

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 bf fe 67 ed 00 15d+00:48:12.896 READ DMA EXT
25 00 08 b7 fe 67 ed 00 15d+00:41:48.483 READ DMA EXT
25 00 08 af fe 67 ed 00 15d+00:41:48.482 READ DMA EXT
25 00 08 a7 fe 67 ed 00 15d+00:41:48.480 READ DMA EXT
25 00 08 9f fe 67 ed 00 15d+00:41:48.479 READ DMA EXT

SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 5569 -

SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

root@data20:/home/tpm#









root@data20:/home/tpm# smartctl --all /dev/sdd
smartctl 5.40 2010-07-12 r3124 [i686-pc-linux-gnu] (local build)
Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net

=== START OF INFORMATION SECTION ===
Model Family: Hitachi Deskstar 7K1000.C
Device Model: Hitachi HDS721010CLA332
Serial Number: JP2940HD0889UC
Firmware Version: JP4OA3EA
User Capacity: 1.000.204.886.016 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 8
ATA Standard is: ATA-8-ACS revision 4
Local Time is: Sat Jul 9 15:06:19 2011 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status: (0x85) Offline data collection activity
was aborted by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (9694) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 162) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail Always - 0
2 Throughput_Performance 0x0005 136 136 054 Pre-fail Offline - 94
3 Spin_Up_Time 0x0007 160 160 024 Pre-fail Always - 199 (Average 275)
4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 74
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 138 138 020 Pre-fail Offline - 31
9 Power_On_Hours 0x0012 100 100 000 Old_age Always - 5440
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 74
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 269
193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always - 269
194 Temperature_Celsius 0x0002 153 153 000 Old_age Always - 39 (Lifetime Min/Max 18/51)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 199 199 000 Old_age Always - 5876

SMART Error Log Version: 1
ATA Error Count: 621 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 621 occurred at disk power-on lifetime: 5428 hours (226 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 b1 8e b8 3a 03 Error: ICRC, ABRT 177 sectors at LBA = 0x033ab88e = 54179982

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 00 3f b8 3a e3 00 38d+10:23:28.015 READ DMA EXT
25 00 00 3f b4 3a e3 00 38d+10:23:27.940 READ DMA EXT
25 00 00 3f b0 3a e0 00 38d+10:23:27.867 READ DMA EXT
ec 00 01 00 00 00 00 00 38d+10:23:27.858 IDENTIFY DEVICE
25 00 80 bf ac 3a e3 00 38d+10:23:27.790 READ DMA EXT

Error 620 occurred at disk power-on lifetime: 5428 hours (226 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 c1 7e 91 39 03 Error: ICRC, ABRT 193 sectors at LBA = 0x0339917e = 54104446

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 00 3f 91 39 e3 00 38d+10:20:12.106 READ DMA EXT
25 00 00 3f 8d 39 e3 00 38d+10:20:12.031 READ DMA EXT
25 00 00 3f 89 39 e3 00 38d+10:20:11.957 READ DMA EXT
25 00 00 3f 85 39 e3 00 38d+10:20:11.882 READ DMA EXT
25 00 00 3f 81 39 e3 00 38d+10:20:11.807 READ DMA EXT

Error 619 occurred at disk power-on lifetime: 5428 hours (226 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 e1 5e a1 38 03 Error: ICRC, ABRT 225 sectors at LBA = 0x0338a15e = 54042974

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 00 3f a1 38 e3 00 38d+10:20:05.254 READ DMA EXT
25 00 00 3f 9d 38 e3 00 38d+10:20:05.180 READ DMA EXT
25 00 00 3f 99 38 e3 00 38d+10:20:05.105 READ DMA EXT
25 00 00 3f 95 38 e3 00 38d+10:20:05.030 READ DMA EXT
25 00 00 3f 91 38 e3 00 38d+10:20:04.956 READ DMA EXT

Error 618 occurred at disk power-on lifetime: 5428 hours (226 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 b1 8e 6d 37 03 Error: ICRC, ABRT 177 sectors at LBA = 0x03376d8e = 53964174

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 00 3f 6d 37 e3 00 38d+10:19:59.344 READ DMA EXT
25 00 00 3f 69 37 e3 00 38d+10:19:59.269 READ DMA EXT
25 00 00 3f 65 37 e3 00 38d+10:19:59.195 READ DMA EXT
25 00 00 3f 61 37 e3 00 38d+10:19:59.120 READ DMA EXT
25 00 00 3f 5d 37 e3 00 38d+10:19:59.045 READ DMA EXT

Error 617 occurred at disk power-on lifetime: 5428 hours (226 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 b1 8e 59 35 03 Error: ICRC, ABRT 177 sectors at LBA = 0x0335598e = 53827982

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 00 3f 59 35 e3 00 38d+10:19:47.045 READ DMA EXT
25 00 00 3f 55 35 e3 00 38d+10:19:46.970 READ DMA EXT
25 00 00 3f 51 35 e3 00 38d+10:19:46.895 READ DMA EXT
25 00 00 3f 4d 35 e3 00 38d+10:19:46.821 READ DMA EXT
25 00 00 3f 49 35 e3 00 38d+10:19:46.746 READ DMA EXT

SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 5440 -
# 2 Extended offline Interrupted (host reset) 90% 5428 -

SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

root@data20:/home/tpm#

















root@data20:/home/tpm# fdisk -l

Disk /dev/sda: 1000.2 GB, 1000204886016 bytes
255 heads, 63 sectors/track, 121601 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x00000000

Device Boot Start End Blocks Id System
/dev/sda1 1 121601 976759008+ fd Linux raid autodetect

Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes
255 heads, 63 sectors/track, 121601 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x00000000

Device Boot Start End Blocks Id System
/dev/sdb1 1 121601 976759008+ fd Linux raid autodetect

Disk /dev/sdc: 1000.2 GB, 1000204886016 bytes
255 heads, 63 sectors/track, 121601 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x00000000

Device Boot Start End Blocks Id System
/dev/sdc1 1 121601 976760001 fd Linux raid autodetect

Disk /dev/sde: 20.6 GB, 20576747520 bytes
255 heads, 63 sectors/track, 2501 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x0005d07c

Device Boot Start End Blocks Id System
/dev/sde1 * 1 2394 19225600 83 Linux

Disk /dev/sdd: 1000.2 GB, 1000204886016 bytes
255 heads, 63 sectors/track, 121601 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x00000000

Device Boot Start End Blocks Id System
/dev/sdd1 1 121601 976760001 fd Linux raid autodetect

Disk /dev/sdf: 80.0 GB, 80026361856 bytes
255 heads, 63 sectors/track, 9729 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x00000000

Device Boot Start End Blocks Id System
/dev/sdf1 1 9729 78148161 83 Linux

Disk /dev/md1: 1000.2 GB, 1000200036352 bytes
2 heads, 4 sectors/track, 244189462 cylinders
Units = cylinders of 8 * 512 = 4096 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x00000000

Disk /dev/md1 doesn't contain a valid partition table
root@data20:/home/tpm#
















root@data20:/home/tpm# cat /etc/mdadm/mdadm.conf
# mdadm.conf
#
# Please refer to mdadm.conf(5) for information about this file.
#

# by default, scan all partitions (/proc/partitions) for MD superblocks.
# alternatively, specify devices to scan, using wildcards if desired.
# DEVICE

# auto-create devices with Debian standard permissions
CREATE owner=root group=disk mode=0660 auto=yes

# automatically tag new arrays as belonging to the local system
HOMEHOST <system>

# instruct the monitoring daemon where to send mail alerts
MAILADDR root

# definitions of existing MD arrays

# This file was auto-generated on Sun, 01 May 2011 23:09:09 +0200
# by mkconf 3.1.4-1+8efb9d1
ARRAY /dev/md0 level=raid1 num-devices=2 metadata=1.2 name=data20:0 UUID=abc7a67a:b37230d8:e1acc00a:a814ebbe
ARRAY /dev/md1 level=raid1 num-devices=2 metadata=1.2 name=data20:0 UUID=d003e13c:63be8459:495c808c:ddd0b9d8

root@data20:/home/tpm#










root@data20:/home/tpm# dmesg
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.32-5-686 (Debian 2.6.32-31) (ben@decadent.org.uk) (gcc version 4.3.5 (Debian 4.3.5-4) ) #1 SMP Tue Mar 8 21:36:00 UTC 2011
[ 0.000000] KERNEL supported cpus:
[ 0.000000] Intel GenuineIntel
[ 0.000000] AMD AuthenticAMD
[ 0.000000] NSC Geode by NSC
[ 0.000000] Cyrix CyrixInstead
[ 0.000000] Centaur CentaurHauls
[ 0.000000] Transmeta GenuineTMx86
[ 0.000000] Transmeta TransmetaCPU
[ 0.000000] UMC UMC UMC UMC
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000005fff0000 (usable)
[ 0.000000] BIOS-e820: 000000005fff0000 - 000000005fff8000 (ACPI data)
[ 0.000000] BIOS-e820: 000000005fff8000 - 0000000060000000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
[ 0.000000] DMI 2.3 present.
[ 0.000000] AMI BIOS detected: BIOS may corrupt low RAM, working around it.
[ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[ 0.000000] last_pfn = 0x5fff0 max_arch_pfn = 0x100000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-C7FFF write-protect
[ 0.000000] C8000-EFFFF uncachable
[ 0.000000] F0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask FC0000000 write-back
[ 0.000000] 1 base 040000000 mask FE0000000 write-back
[ 0.000000] 2 disabled
[ 0.000000] 3 disabled
[ 0.000000] 4 disabled
[ 0.000000] 5 base 0E0000000 mask FFC000000 write-combining
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] initial memory mapped : 0 - 01800000
[ 0.000000] init_memory_mapping: 0000000000000000-00000000373fe000
[ 0.000000] 0000000000 - 0000400000 page 4k
[ 0.000000] 0000400000 - 0037000000 page 2M
[ 0.000000] 0037000000 - 00373fe000 page 4k
[ 0.000000] kernel direct mapping tables up to 373fe000 @ 10000-16000
[ 0.000000] RAMDISK: 37774000 - 37fefb8f
[ 0.000000] Allocated new RAMDISK: 00100000 - 0097bb8f
[ 0.000000] Move RAMDISK from 0000000037774000 - 0000000037fefb8e to 00100000 - 0097bb8e
[ 0.000000] ACPI: RSDP 000fa510 00014 (v00 AMI )
[ 0.000000] ACPI: RSDT 5fff0000 0002C (v01 AMIINT VIA_K7 00000010 MSFT 00000097)
[ 0.000000] ACPI: FACP 5fff0030 00081 (v01 AMIINT VIA_K7 00000011 MSFT 00000097)
[ 0.000000] ACPI: DSDT 5fff0120 0315C (v01 VIA VIA_K7 00001000 MSFT 0100000D)
[ 0.000000] ACPI: FACS 5fff8000 00040
[ 0.000000] ACPI: APIC 5fff00c0 00054 (v01 AMIINT VIA_K7 00000009 MSFT 00000097)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] 651MB HIGHMEM available.
[ 0.000000] 883MB LOWMEM available.
[ 0.000000] mapped low ram: 0 - 373fe000
[ 0.000000] low ram: 0 - 373fe000
[ 0.000000] node 0 low ram: 00000000 - 373fe000
[ 0.000000] node 0 bootmap 00012000 - 00018e80
[ 0.000000] (9 early reservations) ==> bootmem [0000000000 - 00373fe000]
[ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
[ 0.000000] #1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000]
[ 0.000000] #2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000]
[ 0.000000] #3 [0001000000 - 00014cabb4] TEXT DATA BSS ==> [0001000000 - 00014cabb4]
[ 0.000000] #4 [000009ec00 - 0000100000] BIOS reserved ==> [000009ec00 - 0000100000]
[ 0.000000] #5 [00014cb000 - 00014d1294] BRK ==> [00014cb000 - 00014d1294]
[ 0.000000] #6 [0000010000 - 0000012000] PGTABLE ==> [0000010000 - 0000012000]
[ 0.000000] #7 [0000100000 - 000097bb8f] NEW RAMDISK ==> [0000100000 - 000097bb8f]
[ 0.000000] #8 [0000012000 - 0000019000] BOOTMAP ==> [0000012000 - 0000019000]
[ 0.000000] found SMP MP-table at [c00fb880] fb880
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] Normal 0x00001000 -> 0x000373fe
[ 0.000000] HighMem 0x000373fe -> 0x0005fff0
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[2] active PFN ranges
[ 0.000000] 0: 0x00000010 -> 0x0000009f
[ 0.000000] 0: 0x00000100 -> 0x0005fff0
[ 0.000000] On node 0 totalpages: 393087
[ 0.000000] free_area_init_node: node 0, pgdat c13b28a0, node_mem_map c14d3200
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 3951 pages, LIFO batch:0
[ 0.000000] Normal zone: 1736 pages used for memmap
[ 0.000000] Normal zone: 220470 pages, LIFO batch:31
[ 0.000000] HighMem zone: 1304 pages used for memmap
[ 0.000000] HighMem zone: 165594 pages, LIFO batch:31
[ 0.000000] Using APIC driver default
[ 0.000000] ACPI: PM-Timer IO Port: 0x808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] SMP: Allowing 1 CPUs, 0 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 24
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
[ 0.000000] PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
[ 0.000000] Allocating PCI resources starting at 60000000 (gap: 60000000:9ec00000)
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] NR_CPUS:32 nr_cpumask_bits:32 nr_cpu_ids:1 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 14 pages/cpu @c2400000 s34328 r0 d23016 u4194304
[ 0.000000] pcpu-alloc: s34328 r0 d23016 u4194304 alloc=1*4194304
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 390015
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.32-5-686 root=UUID=7f2be9e6-0302-4e71-beb9-25798ad5eb1f ro quiet
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] Initializing HighMem for node 0 (000373fe:0005fff0)
[ 0.000000] Memory: 1544616k/1572800k available (2503k kernel code, 26824k reserved, 1321k data, 380k init, 667592k highmem)
[ 0.000000] virtual kernel memory layout:
[ 0.000000] fixmap : 0xffd56000 - 0xfffff000 (2724 kB)
[ 0.000000] pkmap : 0xff400000 - 0xff800000 (4096 kB)
[ 0.000000] vmalloc : 0xf7bfe000 - 0xff3fe000 ( 120 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xf73fe000 ( 883 MB)
[ 0.000000] .init : 0xc13bd000 - 0xc141c000 ( 380 kB)
[ 0.000000] .data : 0xc1271cc1 - 0xc13bc4c0 (1321 kB)
[ 0.000000] .text : 0xc1000000 - 0xc1271cc1 (2503 kB)
[ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:1280
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 1150.063 MHz processor.
[ 0.004010] Calibrating delay loop (skipped), value calculated using timer frequency.. 2300.12 BogoMIPS (lpj=4600252)
[ 0.004058] Security Framework initialized
[ 0.004074] SELinux: Disabled at boot.
[ 0.004090] Mount-cache hash table entries: 512
[ 0.004393] Initializing cgroup subsys ns
[ 0.004402] Initializing cgroup subsys cpuacct
[ 0.004411] Initializing cgroup subsys devices
[ 0.004417] Initializing cgroup subsys freezer
[ 0.004422] Initializing cgroup subsys net_cls
[ 0.004476] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 0.004482] CPU: L2 Cache: 256K (64 bytes/line)
[ 0.004491] mce: CPU supports 4 MCE banks
[ 0.004535] Performance Events: AMD PMU driver.
[ 0.004549] ... version: 0
[ 0.004553] ... bit width: 48
[ 0.004557] ... generic registers: 4
[ 0.004561] ... value mask: 0000ffffffffffff
[ 0.004565] ... max period: 00007fffffffffff
[ 0.004569] ... fixed-purpose events: 0
[ 0.004573] ... event mask: 000000000000000f
[ 0.004582] Checking 'hlt' instruction... OK.
[ 0.020502] SMP alternatives: switching to UP code
[ 0.026653] Freeing SMP alternatives: 13k freed
[ 0.026689] ACPI: Core revision 20090903
[ 0.033946] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.035289] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.074982] CPU0: AMD Athlon(tm) Processor stepping 02
[ 0.076001] Brought up 1 CPUs
[ 0.076001] Total of 1 processors activated (2300.12 BogoMIPS).
[ 0.076001] CPU0 attaching NULL sched-domain.
[ 0.076001] devtmpfs: initialized
[ 0.076001] regulator: core version 0.5
[ 0.076001] NET: Registered protocol family 16
[ 0.076001] ACPI: bus type pci registered
[ 0.076125] PCI: PCI BIOS revision 2.10 entry at 0xfdb21, last bus=1
[ 0.076131] PCI: Using configuration type 1 for base access
[ 0.076899] bio: create slab <bio-0> at 0
[ 0.077654] ACPI: EC: Look up EC in DSDT
[ 0.085619] ACPI: Interpreter enabled
[ 0.085628] ACPI: (supports S0 S1 S4 S5)
[ 0.085665] ACPI: Using IOAPIC for interrupt routing
[ 0.091900] ACPI: Power Resource [URP1] (off)
[ 0.091953] ACPI: Power Resource [URP2] (off)
[ 0.092015] ACPI: Power Resource [FDDP] (off)
[ 0.092069] ACPI: Power Resource [LPTP] (off)
[ 0.092272] ACPI: No dock devices found.
[ 0.092502] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.092592] pci 0000:00:00.0: reg 10 32bit mmio pref: [0xe0000000-0xe3ffffff]
[ 0.092712] pci 0000:00:01.0: supports D1
[ 0.092760] pci 0000:00:07.0: reg 10 io port: [0xec00-0xec07]
[ 0.092771] pci 0000:00:07.0: reg 14 io port: [0xe800-0xe803]
[ 0.092781] pci 0000:00:07.0: reg 18 io port: [0xe400-0xe407]
[ 0.092791] pci 0000:00:07.0: reg 1c io port: [0xe000-0xe003]
[ 0.092801] pci 0000:00:07.0: reg 20 io port: [0xdc00-0xdc0f]
[ 0.092811] pci 0000:00:07.0: reg 24 32bit mmio: [0xdffffe00-0xdfffffff]
[ 0.092822] pci 0000:00:07.0: reg 30 32bit mmio pref: [0xdff00000-0xdff7ffff]
[ 0.092844] pci 0000:00:07.0: supports D1 D2
[ 0.092885] pci 0000:00:08.0: reg 10 io port: [0xd800-0xd807]
[ 0.092895] pci 0000:00:08.0: reg 14 io port: [0xd400-0xd403]
[ 0.092905] pci 0000:00:08.0: reg 18 io port: [0xd000-0xd007]
[ 0.092915] pci 0000:00:08.0: reg 1c io port: [0xcc00-0xcc03]
[ 0.092925] pci 0000:00:08.0: reg 20 io port: [0xc800-0xc80f]
[ 0.092936] pci 0000:00:08.0: reg 24 32bit mmio: [0xdffffc00-0xdffffdff]
[ 0.092947] pci 0000:00:08.0: reg 30 32bit mmio pref: [0xdfe80000-0xdfefffff]
[ 0.092968] pci 0000:00:08.0: supports D1 D2
[ 0.093010] pci 0000:00:09.0: reg 10 io port: [0xc400-0xc4ff]
[ 0.093021] pci 0000:00:09.0: reg 14 32bit mmio: [0xdffffb00-0xdffffbff]
[ 0.093049] pci 0000:00:09.0: reg 30 32bit mmio pref: [0xdffd0000-0xdffdffff]
[ 0.093071] pci 0000:00:09.0: supports D1 D2
[ 0.093076] pci 0000:00:09.0: PME# supported from D1 D2 D3hot
[ 0.093084] pci 0000:00:09.0: PME# disabled
[ 0.093238] pci 0000:00:11.1: reg 20 io port: [0xfc00-0xfc0f]
[ 0.093325] pci 0000:00:11.2: reg 20 io port: [0xb400-0xb41f]
[ 0.093410] pci 0000:00:11.3: reg 20 io port: [0xb800-0xb81f]
[ 0.093494] pci 0000:00:11.4: reg 20 io port: [0xbc00-0xbc1f]
[ 0.093562] pci 0000:00:11.5: reg 10 io port: [0xc000-0xc0ff]
[ 0.093676] pci 0000:01:00.0: reg 10 32bit mmio: [0xde000000-0xdeffffff]
[ 0.093686] pci 0000:01:00.0: reg 14 io port: [0x6800-0x68ff]
[ 0.093696] pci 0000:01:00.0: reg 18 32bit mmio: [0xdfcff000-0xdfcfffff]
[ 0.093718] pci 0000:01:00.0: reg 30 32bit mmio pref: [0xdfcc0000-0xdfcdffff]
[ 0.093781] pci 0000:00:01.0: bridge io port: [0x6000-0x6fff]
[ 0.093788] pci 0000:00:01.0: bridge 32bit mmio: [0xddc00000-0xdfcfffff]
[ 0.093796] pci 0000:00:01.0: bridge 32bit mmio pref: [0xdda00000-0xddafffff]
[ 0.093808] pci_bus 0000:00: on NUMA node 0
[ 0.093817] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.114976] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[ 0.115150] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 0.115321] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[ 0.115490] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11 *12 14 15)
[ 0.115712] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.115718] vgaarb: loaded
[ 0.115921] PCI: Using ACPI for IRQ routing
[ 0.116221] Switching to clocksource tsc
[ 0.118844] pnp: PnP ACPI init
[ 0.118897] ACPI: bus type pnp registered
[ 0.123647] pnp: PnP ACPI: found 11 devices
[ 0.123652] ACPI: ACPI bus type pnp unregistered
[ 0.123662] PnPBIOS: Disabled by ACPI PNP
[ 0.158714] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
[ 0.158721] pci 0000:00:01.0: IO window: 0x6000-0x6fff
[ 0.158731] pci 0000:00:01.0: MEM window: 0xddc00000-0xdfcfffff
[ 0.158739] pci 0000:00:01.0: PREFETCH window: 0xdda00000-0xddafffff
[ 0.158763] pci 0000:00:01.0: setting latency timer to 64
[ 0.158773] pci_bus 0000:00: resource 0 io: [0x00-0xffff]
[ 0.158779] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
[ 0.158786] pci_bus 0000:01: resource 0 io: [0x6000-0x6fff]
[ 0.158792] pci_bus 0000:01: resource 1 mem: [0xddc00000-0xdfcfffff]
[ 0.158798] pci_bus 0000:01: resource 2 pref mem [0xdda00000-0xddafffff]
[ 0.158880] NET: Registered protocol family 2
[ 0.159073] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.159951] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.163003] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.164520] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.164528] TCP reno registered
[ 0.164767] NET: Registered protocol family 1
[ 0.164809] pci 0000:00:01.0: disabling DAC on VIA PCI bridge
[ 0.164881] pci 0000:01:00.0: Boot video device
[ 0.165011] Unpacking initramfs...
[ 0.612519] Freeing initrd memory: 8686k freed
[ 0.635180] audit: initializing netlink socket (disabled)
[ 0.635213] type=2000 audit(1310205868.631:1): initialized
[ 0.641416] highmem bounce pool size: 64 pages
[ 0.641428] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 0.644480] VFS: Disk quotas dquot_6.5.2
[ 0.644602] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.644774] msgmni has been set to 1731
[ 0.645192] alg: No test for stdrng (krng)
[ 0.645248] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.645256] io scheduler noop registered
[ 0.645260] io scheduler anticipatory registered
[ 0.645265] io scheduler deadline registered
[ 0.645333] io scheduler cfq registered (default)
[ 0.645696] isapnp: Scanning for PnP cards...
[ 0.999258] isapnp: No Plug & Play device found
[ 1.002184] Linux agpgart interface v0.103
[ 1.002405] agpgart: Detected VIA KT266/KY266x/KT333 chipset
[ 1.008313] agpgart-via 0000:00:00.0: AGP aperture is 64M @ 0xe0000000
[ 1.008364] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 1.008514] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.008651] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 1.009057] 00:02: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.009237] 00:03: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 1.009581] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[ 1.009586] PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[ 1.010326] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.010510] mice: PS/2 mouse device common for all mice
[ 1.010612] rtc_cmos 00:07: RTC can wake from S4
[ 1.010710] rtc_cmos 00:07: rtc core: registered rtc_cmos as rtc0
[ 1.010766] rtc0: alarms up to one year, y3k, 114 bytes nvram
[ 1.010789] cpuidle: using governor ladder
[ 1.010793] cpuidle: using governor menu
[ 1.010803] No iBFT detected.
[ 1.011645] TCP cubic registered
[ 1.011981] NET: Registered protocol family 10
[ 1.013701] Mobile IPv6
[ 1.013708] NET: Registered protocol family 17
[ 1.013745] Using IPI No-Shortcut mode
[ 1.013901] PM: Resume from disk failed.
[ 1.013936] registered taskstats version 1
[ 1.014358] rtc_cmos 00:07: setting system clock to 2011-07-09 10:04:29 UTC (1310205869)
[ 1.014428] Initalizing network drop monitor service
[ 1.014494] Freeing unused kernel memory: 380k freed
[ 1.015450] Write protecting the kernel text: 2504k
[ 1.015492] Write protecting the kernel read-only data: 920k
[ 1.025778] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[ 1.064043] udev[46]: starting version 164
[ 1.422592] SCSI subsystem initialized
[ 1.474881] libata version 3.00 loaded.
[ 1.487527] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 1.487597] r8169 0000:00:09.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.487657] r8169 0000:00:09.0: no PCI Express capability
[ 1.489345] eth0: RTL8110s at 0xf7dc6b00, 00:50:fc:fe:8d:33, XID 04000000 IRQ 16
[ 1.520350] usbcore: registered new interface driver usbfs
[ 1.520670] usbcore: registered new interface driver hub
[ 1.528986] Floppy drive(s): fd0 is 1.44M
[ 1.529968] usbcore: registered new device driver usb
[ 1.534686] sata_sil 0000:00:07.0: version 2.4
[ 1.534804] sata_sil 0000:00:07.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 1.543026] scsi0 : sata_sil
[ 1.544151] scsi1 : sata_sil
[ 1.544432] ata1: SATA max UDMA/100 mmio m512@0xdffffe00 tf 0xdffffe80 irq 18
[ 1.544440] ata2: SATA max UDMA/100 mmio m512@0xdffffe00 tf 0xdffffec0 irq 18
[ 1.544582] sata_sil 0000:00:08.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[ 1.544833] scsi2 : sata_sil
[ 1.546246] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.547878] FDC 0 is a post-1991 82077
[ 1.547939] scsi3 : sata_sil
[ 1.548138] ata3: SATA max UDMA/100 mmio m512@0xdffffc00 tf 0xdffffc80 irq 19
[ 1.548146] ata4: SATA max UDMA/100 mmio m512@0xdffffc00 tf 0xdffffcc0 irq 19
[ 1.574764] pata_via 0000:00:11.1: version 0.3.4
[ 1.575167] scsi4 : pata_via
[ 1.575491] scsi5 : pata_via
[ 1.579515] ata5: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xfc00 irq 14
[ 1.579524] ata6: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xfc08 irq 15
[ 1.627245] uhci_hcd: USB Universal Host Controller Interface driver
[ 1.627396] uhci_hcd 0000:00:11.2: PCI INT D -> GSI 12 (level, low) -> IRQ 12
[ 1.627417] uhci_hcd 0000:00:11.2: UHCI Host Controller
[ 1.627488] uhci_hcd 0000:00:11.2: new USB bus registered, assigned bus number 1
[ 1.627553] uhci_hcd 0000:00:11.2: irq 12, io base 0x0000b400
[ 1.627653] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.627660] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.627667] usb usb1: Product: UHCI Host Controller
[ 1.627671] usb usb1: Manufacturer: Linux 2.6.32-5-686 uhci_hcd
[ 1.627676] usb usb1: SerialNumber: 0000:00:11.2
[ 1.628119] usb usb1: configuration #1 chosen from 1 choice
[ 1.628274] hub 1-0:1.0: USB hub found
[ 1.628301] hub 1-0:1.0: 2 ports detected
[ 1.628423] uhci_hcd 0000:00:11.3: PCI INT D -> GSI 12 (level, low) -> IRQ 12
[ 1.628441] uhci_hcd 0000:00:11.3: UHCI Host Controller
[ 1.628460] uhci_hcd 0000:00:11.3: new USB bus registered, assigned bus number 2
[ 1.628495] uhci_hcd 0000:00:11.3: irq 12, io base 0x0000b800
[ 1.628573] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.628580] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.628586] usb usb2: Product: UHCI Host Controller
[ 1.628590] usb usb2: Manufacturer: Linux 2.6.32-5-686 uhci_hcd
[ 1.628595] usb usb2: SerialNumber: 0000:00:11.3
[ 1.628826] usb usb2: configuration #1 chosen from 1 choice
[ 1.629340] hub 2-0:1.0: USB hub found
[ 1.629368] hub 2-0:1.0: 2 ports detected
[ 1.629488] uhci_hcd 0000:00:11.4: PCI INT D -> GSI 12 (level, low) -> IRQ 12
[ 1.629506] uhci_hcd 0000:00:11.4: UHCI Host Controller
[ 1.629534] uhci_hcd 0000:00:11.4: new USB bus registered, assigned bus number 3
[ 1.629572] uhci_hcd 0000:00:11.4: irq 12, io base 0x0000bc00
[ 1.629656] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.629662] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.629668] usb usb3: Product: UHCI Host Controller
[ 1.629673] usb usb3: Manufacturer: Linux 2.6.32-5-686 uhci_hcd
[ 1.629678] usb usb3: SerialNumber: 0000:00:11.4
[ 1.629937] usb usb3: configuration #1 chosen from 1 choice
[ 1.630082] hub 3-0:1.0: USB hub found
[ 1.630103] hub 3-0:1.0: 2 ports detected
[ 1.752731] ata5.00: ATA-5: IC35L020AVVN07-0, VA1OAF0C, max UDMA/100
[ 1.752741] ata5.00: 40188960 sectors, multi 16: LBA
[ 1.776627] ata5.00: configured for UDMA/100
[ 1.864032] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1.872034] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1.872547] ata1.00: ATA-8: ST31000524AS, JC45, max UDMA/133
[ 1.872554] ata1.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 1.880388] ata3.00: ATA-8: Hitachi HDS721010CLA332, JP4OA3EA, max UDMA/133
[ 1.880396] ata3.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 1.888534] ata1.00: configured for UDMA/100
[ 1.888792] scsi 0:0:0:0: Direct-Access ATA ST31000524AS JC45 PQ: 0 ANSI: 5
[ 1.896500] ata3.00: configured for UDMA/100
[ 2.208036] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 2.216405] ata2.00: ATA-8: ST31000524AS, JC45, max UDMA/133
[ 2.216413] ata2.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 2.232427] ata2.00: configured for UDMA/100
[ 2.232700] scsi 1:0:0:0: Direct-Access ATA ST31000524AS JC45 PQ: 0 ANSI: 5
[ 2.233788] scsi 2:0:0:0: Direct-Access ATA Hitachi HDS72101 JP4O PQ: 0 ANSI: 5
[ 2.248209] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[ 2.248327] sd 0:0:0:0: [sda] Write Protect is off
[ 2.248335] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 2.248386] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.248695] sda:
[ 2.249091] sd 1:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[ 2.249197] sd 1:0:0:0: [sdb] Write Protect is off
[ 2.249204] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 2.249252] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.249514] sdb:
[ 2.249834] sd 2:0:0:0: [sdc] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[ 2.249940] sd 2:0:0:0: [sdc] Write Protect is off
[ 2.249947] sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 2.249995] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.250276] sdc: sda1
[ 2.268380] sd 0:0:0:0: [sda] Attached SCSI disk
[ 2.270582] sdc1
[ 2.271764] sd 2:0:0:0: [sdc] Attached SCSI disk
[ 2.273389] sdb1
[ 2.274617] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 2.556039] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 2.564389] ata4.00: ATA-8: Hitachi HDS721010CLA332, JP4OA3EA, max UDMA/133
[ 2.564397] ata4.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 2.580388] ata4.00: configured for UDMA/100
[ 2.580599] scsi 3:0:0:0: Direct-Access ATA Hitachi HDS72101 JP4O PQ: 0 ANSI: 5
[ 2.581146] scsi 4:0:0:0: Direct-Access ATA IC35L020AVVN07-0 VA1O PQ: 0 ANSI: 5
[ 2.581612] sd 4:0:0:0: [sde] 40188960 512-byte logical blocks: (20.5 GB/19.1 GiB)
[ 2.581724] sd 4:0:0:0: [sde] Write Protect is off
[ 2.581731] sd 4:0:0:0: [sde] Mode Sense: 00 3a 00 00
[ 2.582297] sd 4:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.582504] sd 3:0:0:0: [sdd] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[ 2.582627] sd 3:0:0:0: [sdd] Write Protect is off
[ 2.582634] sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 2.582725] sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.582915] sde:
[ 2.583214] sdd: sdd1
[ 2.600902] sd 3:0:0:0: [sdd] Attached SCSI disk
[ 2.601035] sde1
[ 2.602211] sd 4:0:0:0: [sde] Attached SCSI disk
[ 2.800581] ata6.00: ATA-6: ST380011A, 3.06, max UDMA/100
[ 2.800589] ata6.00: 156301488 sectors, multi 16: LBA48
[ 2.816464] ata6.00: configured for UDMA/100
[ 2.816665] scsi 5:0:0:0: Direct-Access ATA ST380011A 3.06 PQ: 0 ANSI: 5
[ 2.817140] sd 5:0:0:0: [sdf] 156301488 512-byte logical blocks: (80.0 GB/74.5 GiB)
[ 2.817254] sd 5:0:0:0: [sdf] Write Protect is off
[ 2.817261] sd 5:0:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 2.817664] sd 5:0:0:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.817956] sdf: sdf1
[ 2.822308] sd 5:0:0:0: [sdf] Attached SCSI disk
[ 3.185424] md: linear personality registered for level -1
[ 3.192152] md: multipath personality registered for level -4
[ 3.197884] md: raid0 personality registered for level 0
[ 3.207515] md: raid1 personality registered for level 1
[ 3.212769] async_tx: api initialized (async)
[ 3.215812] xor: automatically using best checksumming function: pIII_sse
[ 3.232010] pIII_sse : 1389.000 MB/sec
[ 3.232015] xor: using function: pIII_sse (1389.000 MB/sec)
[ 3.304115] raid6: int32x1 473 MB/s
[ 3.372065] raid6: int32x2 500 MB/s
[ 3.440049] raid6: int32x4 421 MB/s
[ 3.508193] raid6: int32x8 332 MB/s
[ 3.576012] raid6: mmxx1 929 MB/s
[ 3.644024] raid6: mmxx2 1571 MB/s
[ 3.712061] raid6: sse1x1 861 MB/s
[ 3.780042] raid6: sse1x2 1397 MB/s
[ 3.780047] raid6: using algorithm sse1x2 (1397 MB/s)
[ 3.796102] md: raid6 personality registered for level 6
[ 3.796110] md: raid5 personality registered for level 5
[ 3.796115] md: raid4 personality registered for level 4
[ 3.812609] md: raid10 personality registered for level 10
[ 3.897039] md: md0 stopped.
[ 3.999034] md: md1 stopped.
[ 4.004764] md: bind<sdb1>
[ 4.007767] raid1: raid set md1 active with 1 out of 2 mirrors
[ 4.007834] md1: detected capacity change from 0 to 1000200036352
[ 4.013490] md1: unknown partition table
[ 4.233817] md: md0 stopped.
[ 4.340213] kjournald starting. Commit interval 5 seconds
[ 4.340239] EXT3-fs: mounted filesystem with ordered data mode.
[ 5.883549] udev[318]: starting version 164
[ 6.799399] processor LNXCPU:00: registered as cooling_device0
[ 6.805962] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1
[ 6.805986] ACPI: Power Button [PWRB]
[ 6.807757] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input2
[ 6.807788] ACPI: Sleep Button [SLPB]
[ 6.808216] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[ 6.808226] ACPI: Power Button [PWRF]
[ 6.825073] input: PC Speaker as /devices/platform/pcspkr/input/input4
[ 6.864595] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 7.006498] parport_pc 00:04: reported by Plug and Play ACPI
[ 7.006619] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE,EPP]
[ 7.075237] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 7.141578] gameport: NS558 PnP Gameport is pnp00:05/gameport0, io 0x200, speed 946kHz
[ 7.171379] NET: Registered protocol family 23
[ 7.672346] Error: Driver 'pcspkr' is already registered, aborting...
[ 7.761354] VIA 82xx Audio 0000:00:11.5: PCI INT C -> GSI 10 (level, low) -> IRQ 10
[ 7.761535] VIA 82xx Audio 0000:00:11.5: setting latency timer to 64
[ 8.431279] md: md0 stopped.
[ 9.100389] EXT3 FS on sde1, internal journal
[ 9.279748] loop: module loaded
[ 10.194418] kjournald starting. Commit interval 5 seconds
[ 10.214161] EXT3 FS on md1, internal journal
[ 10.214175] EXT3-fs: mounted filesystem with ordered data mode.
[ 10.294563] kjournald starting. Commit interval 5 seconds
[ 10.294586] EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
[ 10.294859] EXT3 FS on sdf1, internal journal
[ 10.294870] EXT3-fs: mounted filesystem with ordered data mode.
[ 11.350014] RPC: Registered udp transport module.
[ 11.350023] RPC: Registered tcp transport module.
[ 11.350027] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 11.426038] Slow work thread pool: Starting up
[ 11.426162] Slow work thread pool: Ready
[ 11.426317] FS-Cache: Loaded
[ 11.501037] FS-Cache: Netfs 'nfs' registered for caching
[ 11.548190] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 11.802207] r8169: eth0: link up
[ 13.527218] svc: failed to register lockdv1 RPC service (errno 97).
[ 13.529646] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
[ 13.551200] NFSD: starting 90-second grace period
[ 22.384013] eth0: no IPv6 routers present
root@data20:/home/tpm#




















root@data20:/home/tpm# cat /etc/fstab
# /etc/fstab: static file system information.
#
# Use 'blkid' to print the universally unique identifier for a
# device; this may be used with UUID= as a more robust way to name devices
# that works even if disks are added and removed. See fstab(5).
#
# <file system> <mount point> <type> <options> <dump> <pass>
proc /proc proc defaults 0 0
# / was on /dev/sda1 during installation
UUID=7f2be9e6-0302-4e71-beb9-25798ad5eb1f / ext3 errors=remount-ro 0 1
# swap was on /dev/sda5 during installation
UUID=26791c44-f4bb-407b-819f-5271a8fd3edc none swap sw 0 0
/dev/scd0 /media/cdrom0 udf,iso9660 user,noauto 0 0
/dev/fd0 /media/floppy0 auto rw,user,noauto 0 0
/dev/md0 /media/md0 auto rw,user 0 0
/dev/md1 /media/md1 auto rw,user 0 0
/dev/sdf1 /media/hdc1 auto rw,user 0 0

root@data20:/home/tpm#








Jul 8 16:37:10 data20 kernel: [ 70.180491] ata6.00: configured for UDMA/100
Jul 8 16:37:10 data20 kernel: [ 70.180536] ata6: EH complete
Jul 8 16:37:10 data20 kernel: [ 70.212394] ata6.00: configured for UDMA/100
Jul 8 16:37:10 data20 kernel: [ 70.212421] ata6: EH complete
Jul 8 16:37:10 data20 kernel: [ 70.258893] ata6: hard resetting link
Jul 8 16:37:11 data20 kernel: [ 70.576061] ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
Jul 8 16:37:11 data20 kernel: [ 70.600391] ata6.00: configured for UDMA/100
Jul 8 16:37:11 data20 kernel: [ 70.600428] ata6: EH complete
Jul 8 16:37:11 data20 kernel: [ 70.693823] ata6.00: limiting speed to UDMA/66:PIO4
Jul 8 16:37:11 data20 kernel: [ 70.694266] ata6: hard resetting link
Jul 8 16:37:11 data20 kernel: [ 71.012037] ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
Jul 8 16:37:11 data20 kernel: [ 71.036388] ata6.00: configured for UDMA/66
Jul 8 16:37:11 data20 kernel: [ 71.036425] ata6: EH complete
Jul 8 16:37:11 data20 kernel: [ 71.072406] ata6.00: configured for UDMA/66
Jul 8 16:37:11 data20 kernel: [ 71.072447] ata6: EH complete
Jul 8 16:37:42 data20 kernel: [ 101.816388] ata6: hard resetting link
Jul 8 16:37:42 data20 kernel: [ 102.136039] ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
Jul 8 16:37:42 data20 kernel: [ 102.160408] ata6.00: configured for UDMA/66
Jul 8 16:37:42 data20 kernel: [ 102.160445] ata6: EH complete
Jul 8 16:37:43 data20 kernel: [ 102.653376] ata6: hard resetting link
Jul 8 16:37:43 data20 kernel: [ 102.972036] ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
Jul 8 16:37:43 data20 kernel: [ 102.996387] ata6.00: configured for UDMA/66
Jul 8 16:37:43 data20 kernel: [ 102.996414] ata6: EH complete
Jul 8 16:38:14 data20 kernel: [ 133.816380] ata6: hard resetting link
Jul 8 16:38:14 data20 kernel: [ 134.136041] ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
Jul 8 16:38:14 data20 kernel: [ 134.160414] ata6.00: configured for UDMA/66
Jul 8 16:38:14 data20 kernel: [ 134.160445] ata6: EH complete












root@data20:/home/tpm# lspci
00:00.0 Host bridge: VIA Technologies, Inc. VT8366/A/7 [Apollo KT266/A/333]
00:01.0 PCI bridge: VIA Technologies, Inc. VT8366/A/7 [Apollo KT266/A/333 AGP]
00:07.0 RAID bus controller: Silicon Image, Inc. SiI 3512 [SATALink/SATARaid] Serial ATA Controller (rev 01)
00:08.0 RAID bus controller: Silicon Image, Inc. SiI 3512 [SATALink/SATARaid] Serial ATA Controller (rev 01)
00:09.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8169 Gigabit Ethernet (rev 10)
00:11.0 ISA bridge: VIA Technologies, Inc. VT8233 PCI to ISA Bridge
00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
00:11.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 1b)
00:11.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 1b)
00:11.4 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 1b)
00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 10)
01:00.0 VGA compatible controller: ATI Technologies Inc 3D Rage Pro AGP 1X/2X (rev 5c)
root@data20:/home/tpm#




root@data20:/home/tpm# ls /dev/
agpgart fd loop1 md psaux sdb sdf1 tty0 tty17 tty25 tty33 tty41 tty5 tty58 tty9 vcs3 vcsa5
block fd0 loop2 md1 ptmx sdb1 shm tty1 tty18 tty26 tty34 tty42 tty50 tty59 ttyS0 vcs4 vcsa6
bsg full loop3 mem pts sdc snapshot tty10 tty19 tty27 tty35 tty43 tty51 tty6 ttyS1 vcs5 vga_arbiter
bus hpet loop4 net random sdc1 snd tty11 tty2 tty28 tty36 tty44 tty52 tty60 ttyS2 vcs6 xconsole
char initctl loop5 network_latency root sdd sndstat tty12 tty20 tty29 tty37 tty45 tty53 tty61 ttyS3 vcsa zero
console input loop6 network_throughput rtc sdd1 stderr tty13 tty21 tty3 tty38 tty46 tty54 tty62 urandom vcsa1
core kmsg loop7 null rtc0 sde stdin tty14 tty22 tty30 tty39 tty47 tty55 tty63 vcs vcsa2
cpu_dma_latency log MAKEDEV port sda sde1 stdout tty15 tty23 tty31 tty4 tty48 tty56 tty7 vcs1 vcsa3
disk loop0 mcelog ppp sda1 sdf tty tty16 tty24 tty32 tty40 tty49 tty57 tty8 vcs2 vcsa4
root@data20:/home/tpm#







root@data20:/home/tpm# cat /proc/mdstat
Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10]
md1 : active raid1 sdb1[0]
976757848 blocks super 1.2 [2/1] [U_]

unused devices: <none>
root@data20:/home/tpm#